Monday, June 8, 2009

Zyxel Prestige 650H-E STREAMYX MODEM

Accessing Your Prestige via Web Browser

  1. Launch your web browser. Enter http://192.168.1.1 as the web address
  2. Then enter the username and password:
    • Username: admin
    • Password: 1234

    Then click OK

  3. Then click at the wizard setup link
  4. Then you will change the setting as this:
    • Mode: routing OR bridge
    • Encapsulation: PPOE
    • Multiplex: LLC
    • Virtual Circuit ID: VPI -0 & VCI -35

    Then click Next

  5. On the next page change the setting as this:
    • Service Name: Streamyx
    • Username: username@streamyx
    • Password: your TMNet Streamyx password
    • IP Address: Click on the obtain an IP address automatically
    • Connection: Nailed-Up connection (if you want your internet connection to be online all time)
    • Network Address Translation: Choose SUA only
  6. Verify the setting on the next screen. Click on the Save setting
  7. So right now your modem has been configuring to Auto-connection mode

ZTE ZXDSL 831 STREAMYX MODEM

ZTE ZXDSL 831 is a modem / router supplied by TM. It works as a modem by default but you can change it to a router.

In router mode, you don’t need to dial Streamyx manually anymore. The router will dial it for you automatically.

How to Configure ZTE ZXDSL 831 Modem as a Router

  1. Visit http://192.168.1.1 with the username and password. If you don’t know the default username and password:
    • Username: ADSL
    • Password: expert03
  2. When logged in, click on the WAN tab
  3. Click on ATM VC and make sure, interface aal5-0 VPI = 0 & VCI = 35, MUX = LLC, Max proto = 2
  4. Click on PPP and then a new interface
  5. Set the new interface as PPP interface = 0 ATM VC = aal5-0, protocol = PPoE, use DNS = enable, security = PAP. Don’t forget to set your TMNet Streamyx username@streamyx and also your password. Click Submit
  6. After that, click on Admin and then Commit and then Reboot Once it’s done you should check your Internet connectivity by loading your favorite website

Port forwarding ZTE ZXDSL 831 for better Bit torrent speed. I know a lot of you guys are asking for this article so here it goes. Don’t blame me for anything if it doesn’t work for you. I provide no support for this post.

The ZTE ZXDSL 831 supplied by TMNet for its Streamyx service. It’s a cheap but quite powerful DSL bridge / router. It uses the GlobespanVirata chipset which is also known to be used to products like D-Link. Since this company has merged with Conexant, support files for the chipset have been removed. You might be able to find it somewhere.

A bit from the Bit torrent FAQ, The BitTorrent client will normally use ports 6881 to 6889, so when you are adding the ports to your firewall, make sure you cover the whole block. If you don’t know the default password, you should check out ZTE ZXDSL 831 default password.

After you login, click on Services tab. Under NAT Options list box, choose NAT Rule Entry. Click Add to add a new rule:

  • Rule Flavor: RDR
  • Rule ID: 15
  • IF NAME: ALL
  • Protocol: ANY
  • Local Address From: 192.168.1.x (Your Bit torrent Client IP)
  • Local Address To: 192.168.1.x (Your Bit torrent Client IP)
  • Global Address From: 0.0.0.0
  • Global Address To: 0.0.0.0
  • Destination Port From: 6681
  • Destination Port To: 6689

After done all that don’t forget to Click on Admin tab and then Commit and Reboot. Make sure to click Commit then Reboot.

UT-300R2 STREAMYX MODEM

This one is another Certified DSL Modem by TMNET Streamyx.

  1. Open your browser and type http://192.168.1.1 (default modem page)
  2. For Username - ‘admin’, Password - ‘utstar’
  3. At the Main Page, click ‘SETUP’
  4. Click on the connections, and delete all information that has been setup inside it.
  5. Click at New Connection, Put the name as Streamyx, key in your username and password,
  6. Make sure that the setting is set ok such as vpi=0, vci=35 , NAT = disable, Type= PPOE, Keep Alive =0 (need to put 0 to disable it).
  7. Go to Tools, System Commands, Save All, Restart.
  8. Finish.

Stay tune for another type of modem that have the certification of TMNET.

TRIZ MODEM CONFIGURATION

How To Configure Triz Modem

  1. Set PC IP to 192.168.1.2 and Gateway to 192.168.1.1
  2. Click on Internet Explorer and at address bar point to 192.168.1.1. Click Go
  3. When Login Interface pops up, enter as below:
    • LOGIN NAME: admin
    • PASSWORD: telekomst / aaaaaaaa
  4. To set Triz modem to PPPOE, click on WAN at the left side of the frame
  5. Use the default Adapter Pvc0 and Click on Submit
  6. Then you will see WAN Configuration Windows, please follow up this instruction and fill in the form.
    • Bridged: Enable
    • Encapsulation: PPOE LLC
    • Enter your TMNet Streamyx login
      • Username: username@streamyx
      • Password: your TMNet Streamyx password
  7. VCI: 35
  8. VPI: 0
  9. Make sure Automatic Reconnect is tick
  10. Click on Save Setting and Reboot on the Left Frame
  11. Click on the Save and Reboot button (This will write all the settings to the flash memory in the modem)

KASDA STREAMYX MODEM

Here is a simple step by step instruction to turn your KASDA ADSL modem from Bridge mode to Router mode. How to turn KASDA ADSL Modem into Routing Mode.

Add a Root User

  1. Open a browser and type the following URL: http://192.168.1.1/hag/emweb/PopOutUserAdd.htm
  2. Wait for a while and a Popup Dialog box will appear asking for username and password. Type in the following:
    • Username: user
    • Password: password
  3. Now add user page should appear. Add any username you like but make sure the user type is ‘ROOT’
  4. Close your browser now. Please do not switch off the modem as doing so you would lose all steps done from 1 to 3
  5. Open browser and type in http://192.168.1.1
  6. Now Key in the username and password that you have created in step 3
  7. Go the Admin Tab and select the Commit and Reboot, now click the button commit. This should save all the work done from steps 1 to 7

Turn KASDA into Routing Mode

  1. Go to the Home Tab and click on the Quick Configuration
  2. Make sure the following Options are filled in accordingly:
    • ATM Interface: 0
    • Operation Mode: Enabled
    • Encapsulation: PPPoE
    • LLC VPI: 0
    • VCI: 35
    • Default Route: Enable
    • PPP Username: yourname@streamyx
    • Password: your TMNet Streamyx password
  3. Click the Submit button
  4. Next, Select the System Mode. Make sure that all settings (radio button) are set to disable. Click the submit button
  5. Go to the Services Tab
  6. Click the NAT. NAT Options: NAT Global Info. Select the Enable radio button option and click the Submit button
  7. NAT Options: NAT Rule Entry. Click on the Add button. Key in the following:
    • Rule Flavor: NAPT
    • Rule ID: 1
    • IF Name: ALL
    • Protocol: ANY
    • Local Address From: 192.168.1.0
    • Local Address To: 192.168.1.255
  8. Click the Submit Button
  9. Select the DNS
  10. Click on the Enable radio button
  11. Click on the Submit button
  12. Go to Admin Tab
  13. Select the Commit and Reboot
  14. Click on the Commit button
  15. Wait for the screen to refresh and Click on the Reboot Button. Now we are done. Now you can try to open a new browser and you should be able to browse the internet without using the PPPoE dialer from your PC

Huawei SmartAX MT800A CONFIGURATION

  1. Connect to 192.168.1.1
  2. Key in:
    • Username: admin
    • Password: admin
  3. Click on the ATM setting at left side menu
  4. Please make sure that VCI-35, VPI-0, Encapsulation-LLC, Connection Type-PPP
  5. After you choose PPP, it will prompt different table where u need to choose PPPoA/PPPoE - PPPoE, IP Unnumber-Disable, Default Route-Enable, Username: username@streamyx, Password: your password. Then click Submit
  6. Click DHCP Mode and choose DHCP Server
  7. Click IP Filter and select Security Level to None and then Submit
  8. Click Save and Reboot, SaveSubmit, RebootSubmit

D-Link DSL500 CONFIGURATION

Access the Web-based Manager

The Manager PC can now use a web browser to communicate with the Router.

Note: Be sure that the Manager PC is not configured to use a proxy server in the Internet settings. In Windows Internet Explorer, you can check if a proxy server is enabled using the following procedure:

  1. In Windows, click on the START button, go to Settings and choose Control Panel
  2. In the Control Panel window, double-click on the Internet Options icon
  3. Click the Connections tab and click on the LAN Settings button
  4. Verify that the Use proxy server option is NOT checked. If it is checked, click in the checked box to deselect the option and click OK

To use the web-based management software, launch a suitable web browser and direct it to the IP address of the Router. Type in http:// followed by the default IP address, 192.168.0.1 in the address bar of the browser. The URL in the address bar should read: http://192.168.0.1.

In the page that opens, click on the Login to web-based management module button in the center. A new window will appear and you will be prompted for a user name and password to access the web-based manager. Use the default user name admin and password admin for first time set up. You should change the web-based manager access user name and password once you have verified that a connection can be established. The user name and password allows any PC within the same subnet as the Router to access the web-based manager.

Once you have changed the connection method to PPPoE, saved the configuration change and restarted the device, you can proceed to enter authentication information used to connect to the WAN. Follow these steps:

  1. Under PPPoE Login, enter the Login User Name used for your network account. The user name and login password, are used to authenticate the identity of the ADSL client and provide access to the service provider’s network. The user name and login password can be any combination of up to 64 characters
  2. Enter the Login Password
  3. Unless you are instructed to use a different Authentication method, leave the default chap protocol selected. The alternative method, pap, can be selected from the pull-down menu if required by the service provider
  4. Leave the Connect on Demand option as enabled in the pull-down menu. This will allow the Router to establish a WAN connection upon restarting
  5. Leave Idle Time set to the default value 0
  6. Click on the OK button on the bottom of the window. A new screen appears
  7. The Save changes and reboot system message prompt offers two option:
    • You can save the configuration changes and restart the device now by clicking OK; or,
    • If you want to change the user name and password used to access the Web Manager, select the Continue and do ‘Save Changes’ later option and click OK, and go to the System Username and Password menu in the Maintenance folder

PPPoA Connections

The default connection method used by the Router is Point-to-Point-Protocol over ATM (PPPoA). In the PPPoA Configuration window, you must enter the user name and password for network account authentication and
verification. When this information is entered, the changes must be saved and the Router restarted. In the Bridge/Router Configuration window, follow these steps to establish the WAN connection using PPPoA:

  1. Under PPPoA Login, enter the Login User Name used for your network account. The user name and login password, are used to authenticate the identity of the ADSL client and provide access to the service provider’s network. The user name and login password can be any combination of up to 64 characters
  2. Enter the Login Password
  3. Unless you are instructed to use a different Authentication method, leave the default chap protocol selected. The alternative method, pap, can be selected from the pull-down menu if required by the service provider
  4. Leave the Connect on Demand option as enabled in the pull-down menu. This will allow the Router to establish a WAN connection upon restarting
  5. Leave Idle Time set to the default value 0
  6. Click on the OK button on the bottom of the window
  7. Save changes and reboot system message prompt offers two option:
    • You can save the configuration changes and restart the device now by clicking OK; or,
    • If you want to change the user name and password used to access the Web Manager, select the Continue and do ‘Save Changes’ later option and click OK, and go to the System Username and Password menu in the Maintenance folder